Central system
SMP Series
Automatic Coolant Mixing and Supply System
Mixes concentrate and water at the set ratio and supplies each machine automatically.
Learn MoreStop dumping coolant. Keep it in circulation.
More than 30 manufacturers using SELTECcut their coolant costs by up to 30%.
Mixing and supply, concentration control, filtration and spent coolant recycling. Since 2000, SELTEC has focused on one thing, metalworking coolant, and we manage it on your shop floor as one connected system.
The Coolant Cycle in Four Stages
Start with the stage that matters most to you and cut both costs and waste.
Central system
CP03
Intelligent Coolant Management System
Removes solids and tramp oil, suppresses bacterial growth, and controls concentration and temperature in a single unit. Treating coolant before it turns rancid extends its service life.
Learn MoreMachine-side unit
CLEANFIT-DS
Compact Machine-Side Filtration for Coolant and Wash Fluid
Connects directly to a single machine tool or parts washer and cleans its coolant or wash fluid. No piping work and a low entry cost.
Learn MoreCentral system
CRM Series
Spent Coolant Recycling System
Filters and sanitizes rancid coolant that would otherwise be disposed of, bringing it back to a reusable condition.
Learn MoreWhat problem are you dealing with?
No need to know product names. Pick the problem you see on your shop floor and we will point you to the right equipment.
- Coolant concentration drifts and machining quality suffersSupplySMP Series
- Operators mix and top up coolant by handSupplySMP Series
- Fines and sludge keep clogging filters and nozzlesMaintainCP03
- Tramp oil floats on top of the coolantMaintainCP03
- Coolant goes rancid quickly and starts to smellMaintainCP03
- Parts-washer fluid turns cloudy and smells within daysFilterCLEANFIT-DS
- Every machine has its own sump, so a central system is hard to justifyFilterCLEANFIT-DS
- Coolant disposal costs keep climbingRecycleCRM Series
Not on the list? Tell us about your setup and one of our engineers will look into it.
How much could your plant save in a year?
Enter your own figures to estimate annual savings with a CRM Series system. The values below are examples only, so replace them with your actual numbers.
Assumptions: 90% lower wastewater disposal cost, 50% lower coolant purchasing cost, and 20 minutes of maintenance per machine at USD 25 per hour over 240 working days a year. Rough estimate only; results vary by installation.
ESG results
start on the shop floor
For manufacturers, the biggest environmental gains are found in the production process itself. SELTEC equipment cuts coolant consumption and waste oil output, and records the change so you can report your ESG performance with real numbers.
Selected for government programs
Approved supplier under the Korean Ministry of Trade, Industry and Energy Clean Factory program (part of the Korean Green New Deal) for three consecutive years from 2020, and selected for the Ministry of Environment commercialization program for environmental SMEs.
Reduction data ready for reporting
The equipment logs changes in coolant consumption and waste oil output, so you can carry the figures straight into your ESG report.
Safer for operators
Automated mixing and top-up mean less direct handling of chemicals and fewer slips caused by spills and leaks.
A Coolant Circulation Plant Built with SELTEC Systems
How our four core systems connect inside a typical machining plant.
Up to30%less concentrate used
2 to 3×longer coolant life
Up to90%of spent coolant reused
Zeropiping work
Central tankSpent coolantSMP SeriesCP03CRM SeriesCLEANFIT-DS- Freshly mixed coolant
- Filtered coolant
- Coolant in use
- Spent coolant
- Recycled coolant
Central system
SMP Series
Automatic mixing and supply
Mixes concentrate and water at the set ratio and tops up the central tank as needed.
Learn MoreCentral system
CP03
In-process maintenance
Keeps the sump coolant circulating while removing solids and tramp oil. Treating the coolant before it turns rancid extends its service life.
Learn MoreCentral system
CRM Series
Spent coolant recycling
Filters and sanitizes coolant that would otherwise be disposed of, bringing it back to a reusable condition.
Learn MoreMachine-side unit
CLEANFIT-DS
One-to-one filtration for coolant and wash fluid
Connects directly to a single machine tool or parts washer and cleans its coolant or wash fluid. A cyclone separates solids, and microbubbles lift out oil and suppress bacterial growth. It sits right next to the machine with no piping work.
Learn More
SMP, CP03 and CRM serve multiple machine tools from one central tank. CLEANFIT-DS is installed directly on a single machine tool or parts washer.
Tell us about your shop floor.
Phone (Mon to Fri, 9:00 to 18:00 KST)
+82 31 366 3817Quotes and consultation
Share your site conditions and our engineers will propose the right configuration.
Request a ConsultationCatalogs
We will email you product datasheets and catalogs in PDF.
Request a CatalogService for existing customers
Inspection, consumables and repair requests for installed equipment.
Request Service